Stockly.com Forums  

Go Back   Stockly.com Forums > Altair 8800 > Troubleshooting

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 09-01-2009, 02:04 PM
TomL_12953 TomL_12953 is offline
Member
 
Join Date: Jan 2007
Location: Malone, NY USA
Posts: 81
Send a message via AIM to TomL_12953 Send a message via MSN to TomL_12953 Send a message via Yahoo to TomL_12953 Send a message via Skype™ to TomL_12953
Question ACR Volume Too Low

What would cause the output of an ACR cassette interface to be very faint? I tried a friend's ACR board and when I plug its output into an amplifier and do a CSAVE from BASIC, I can hear the correct sound but it's so faint, it's almost lost in the background noise. Is this a problem that's easily fixed?

TIA
Tom Lake
Reply With Quote
  #2  
Old 09-01-2009, 04:41 PM
marty marty is offline
Senior Member
 
Join Date: Jun 2007
Posts: 118
Talking Acr

Hi Tom;
As I have never gotten my ACR to work, It is the blind leading the blind, but, what I would suggest IS get a couple of wire Jumpers that you have or from Radio Shack, and see if this helps -- IC H pin 8 is the output look at it with a 'Scope' if you have one, and compare it to your output from the 'plug in' , where you attach you cassette. (Also check your 'plugs' for corrossion). then you can try this, as I am not an engineer, and it looks like there is a filter made up of R51 and C22, I would leave these alone, so that leaves R 50 and R36, I would jump R36 first and see if it helps, otherwise I would take two jumpers and put in parrellel with R 50 another Resistor to lower its value and see if that helps, R 50 may be a part of the filter, so I wouldn't fool around with it unless I had to.... on R 50 you could put in parrellel another 220K ohm resistor.. and see what it does.....
THANK YOU Marty
Reply With Quote
  #3  
Old 05-17-2010, 10:28 AM
TomL_12953 TomL_12953 is offline
Member
 
Join Date: Jan 2007
Location: Malone, NY USA
Posts: 81
Send a message via AIM to TomL_12953 Send a message via MSN to TomL_12953 Send a message via Yahoo to TomL_12953 Send a message via Skype™ to TomL_12953
Default

Quote:
Originally Posted by TomL_12953 View Post
What would cause the output of an ACR cassette interface to be very faint? I tried a friend's ACR board and when I plug its output into an amplifier and do a CSAVE from BASIC, I can hear the correct sound but it's so faint, it's almost lost in the background noise. Is this a problem that's easily fixed?

TIA
Tom Lake
I finally ot it fixed! the guy who fixed it said:
"The tape write section had some damage. It wasn't even generating a carrier tone. I had to replace 2 chips. They were both binary counters and they simply weren't counting. They were Fairchild 9316s, no longer in production. So I replaced them with compatible 74161s. And that solved the write problem."

Thanks to all who offered to help!

Tom L
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Need Person to Repair ACR TomL_12953 Altair 8800 3 04-30-2010 01:18 AM
Need Person to Repair ACR TomL_12953 Classifieds 0 03-31-2010 01:16 PM


All times are GMT. The time now is 02:31 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.