Stockly.com Forums  

Go Back   Stockly.com Forums > Altair 8800 > Altair 8800

Notices

Reply
 
Thread Tools Display Modes
  #11  
Old 01-03-2009, 12:36 AM
Geoff Harrison Geoff Harrison is offline
Senior Member
 
Join Date: Feb 2007
Posts: 104
Default

Quote:
Originally Posted by Pops Racer View Post
Now trying to figure out how to connect 2SIO to PC. I suspect both circuits are DTE and so must be 'crossed-over' (null-modem) TX -> RX, etc. Do you use DTR and RTS?
If you wire the port as per the MITS manual you end up with an odd hybrid DTE/DCE port. Tx and Rx are set up as though it is a DCE, but it uses the control lines as though it is a DTE. The 6850 requires CTS and DCD to be asserted, so you either have to tie them high in your cable, or give up on hardware handshaking and tie pins 23 & 24 to ground on the 6850 (remember, the signals are inverted on the board), in which case a straight cable will work fine using just the data lines and ground.

Geoff.
Reply With Quote
  #12  
Old 01-03-2009, 04:34 AM
Pops Racer Pops Racer is offline
Junior Member
 
Join Date: Nov 2007
Location: Lakelands, NSW, Australia
Posts: 15
Default

Quote:
Originally Posted by Geoff Harrison View Post
If you wire the port as per the MITS manual you end up with an odd hybrid DTE/DCE port. Tx and Rx are set up as though it is a DCE, but it uses the control lines as though it is a DTE. The 6850 requires CTS and DCD to be asserted, so you either have to tie them high in your cable, or give up on hardware handshaking and tie pins 23 & 24 to ground on the 6850 (remember, the signals are inverted on the board), in which case a straight cable will work fine using just the data lines and ground.

Geoff.
Cool - I have wired it the way that Grant descibes and when I run the echo test I get continuous spaces on the terminal and nothing shows when I type.

Have the board strapped for I/O 20/21 octal. I tried changing the input from port 21 to input from sense switches (port 377) and voila! the transmit works great.

The receive does not work - When single stepping, the IN 020 gets a 377 octal - why would the input from the control register return all 1s?
Reply With Quote
  #13  
Old 01-03-2009, 07:05 AM
Pops Racer Pops Racer is offline
Junior Member
 
Join Date: Nov 2007
Location: Lakelands, NSW, Australia
Posts: 15
Default Problem Solved!

I did some digging to find out why the IN 020 was giving me 377 (all ones).

I thought there might be a problem with the 8T97 buffers and the SINP signal. So out with the cheapo 10MHz scope (that was a good investment for 150 bucks) and start probing. Hmmm - SINP working on IC S - all good.

But the OUT 021 was working perfectly. hmmm - some overlap on the 8T97 chips between Data In and Data Out - maybe it was the chip enable coming out of IC P (7400) - lets go check pin 8 on IC P - The only pin on the whole board that I did not solder!!! arrrgh!

Out with the card - solder pin 8 on IC P. Card back in, hook up computer to serial. Develop more finger calluses toggling in the echo program. Voila! It works! Now on to loading Basic. I've got 5K installed, what will happen with 4K basic? I guess the memory space is set by the loader? Or is is hardcoded in the basic tape?

Thanks for all the help

Cheers
Kelly
Reply With Quote
  #14  
Old 01-03-2009, 10:41 PM
Grant Stockly Grant Stockly is offline
Administrator
 
Join Date: Jan 2005
Posts: 447
Default

Did you have any issues with mounting the motherboard? Where are the pictures?
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Three questions about the Altair 8800 kit sje Altair 8800 4 09-20-2012 12:43 AM
Altair kit up and running. Geoff Harrison Altair 8800 28 02-22-2009 02:28 PM
Altair Kit Ser# 8 arrived in Australia! Lionel Theunissen Altair 8800 1 03-08-2007 05:53 AM
Mark's Altair Kit (Ser#003) Grant Stockly Altair 8800 9 12-22-2006 04:43 PM
AltairKit.com is online! Grant Stockly Announcements 10 11-28-2006 10:20 PM


All times are GMT. The time now is 06:45 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.