|
#1
|
|||
|
|||
Hi Guys. I did not get my teletype working, but now you have inspired me. Sorry, Tom, but I cannot help you yet but perhaps I can if I get mine working.
My problem is that I do not know if my teletype is current loop or RS-232. Do either of you know how I can figure this out? Are there pin voltage settings I could measure? I've always held off because I did not want to take any chances of frying my 2SIO port or my teletype. Would a wrong (mismatched) connection cause harm? Paul |
#2
|
|||
|
|||
Quote:
Tom Lake Last edited by TomL_12953; 07-16-2009 at 01:33 AM. |
#3
|
|||
|
|||
Quote:
Paul |
#4
|
|||
|
|||
Quote:
Tom L |
#5
|
|||
|
|||
tty
Hi Tom L
I will suggest some things that you can check before sending the board back to Geoff, Most of it is elementary, But that is what usually can trip one up... trade the 6850's and see what that does, also check for bent pins-- check all Ic's for bent pins.. check that all the resistors , diodes, caps and transistors are in the ccorrect holes and well soldered on both sides... check that you have it wired right between the jumpers and the connector ( signal table for tty) switch port 0 to an rs232 and wire accordingly and see if it works as an rs232. then get it to work as an rs232 or if it works switch it back to tty... that's all I can think of for now.... THANK YOU Marty |
#6
|
|||
|
|||
Quote:
33 with RS232. They were all current loop. It would only be RS232 if there was a current loop to RS232 converter installed inside or outboard somewhere. Teletype model 43 is possibly RS232... but this is a much more modern "teletype" and is mostly electronic (with dot matrix printhead) rather than the nearly all mechanical model 33. Chris |
#7
|
|||
|
|||
Quote:
Tom Lake |
#8
|
|||
|
|||
What is the current status of the 2SIO? Do you still want me to mail you mine or is Geoff modifying it for 2 RS-232 serial ports?
The other undocumented chip is the MUSIC ROM. Just examine and run at the address of the ROM. It will load the listing byte for byte (from the newsletter) into memory starting at 0000 and begin playing. I will send the VTL-2 manual to Geoff and Tom. Here are instructions for the advanced monitor: ; ; Hardware Debug Monitor for 8080/8085/Z80 processor family ; ; This simple monitor requires NO RAM of any sort. You can use it to ; poke around the system as long as the CPU, a ROM and the UART are ; working. (Hint: if the UART is not working, you can use the polling ; by HDM80 to track down its accessing and debug it). ; ; This monitor provides basic read/modify memory, as well as ; Loop Read/Write functions (useful when hardware debugging). ; ; Commands (must be UPPER-CASE): ; Mxxxx - Display memory at specified address ; Displays one line, enter SPACE for another, RETURN to stop ; Exxxx - Edit memory at specified address ; Prompts with location, enter two digit HEX value, then ; SPACE to proceed to next or RETURN to stop ; Gxxxx - Go (Begin Execution) at specified address ; Rxxxx - Perform Loop-Read at specified address (RESET to stop) ; Wxxxx dd - Perform Loop-Write dd -> specified address (RESET to stop) ; ; Build with DDS XASM tools: ; MACRO HDM80.MAC >HDM80.ASM ; ASM85 HDM80 -t ; ; Dave Dunfield - Aug 4, 2007 ; Grant Stockly - Nov 22, 2007 - Modified for 2SIO at 0,1 ; GETC modified ; PUTC modified ; HINT modified ; ; cStat EQU $10 (020) 2SIO Status Register cData EQU $11 (021) 2SIO Data Register |
#9
|
|||
|
|||
2sio
I just sent the board back to Geoff to convert back to RS-232. I gave up on TTY simply because if my Teletype breaks down, I won't be replacing it and will need port 0 to be usable by more modern terminals. I have an RS-232 to Current Loop converter I can use to drive my Teletype for now. Also, I'm bidding on an SIO-C TTY board on eBay so if I get that, I can use that along with the 2SIO.
Any idea about how long it'll be before you can ship the ACR cassette board pair to Geoff for assembling? Another thing: I have a 64K static RAM board which seems to be working fine so you don't have to bother sending that 64K board you said you'd throw in the deal. Would you have and spare 10-pin female Molex connectors (and metal inserts) I could buy? If not, what's the Molex part number and where do you get them? Thanks for your time. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Simple questions on the replica kit | herby1620 | Altair 680 | 4 | 08-10-2007 10:51 PM |